We're happy to announce that we have a new tool in our quest for making precise, economical, and understandable experiments. HUG has engineered up a water flow calorimeter intended to be used with the small, LENR-stick type test cells. We will use this new calorimeter when we load many types of celani waire into one test cell in the coming days and weeks.

The calorimeter is detailed here: Water Flow Calorimeter Description  (Entire document embedded below, also)

The next step is for us to perform a careful calibration of the instrument with the empty Multi-Wire LENR-Stick.  This should be accomplished with the week.  

The data for this apparatus is not streaming, yet, but will be after calibration.  If anyone has a reliable, relatively new laptop that they would like to donate, we could use one that we could assign exclusively to this apparatus.

Image Gallery

One of the two 1 watt heaters exposed.

View inside the water reservoir where the pumps can be seen with a filter.

View of the Calorimeter, the water reservoir, and the heat pump all together in the lab.

The calorimeter in the lab with the laptop for it.

View of entire apparatus in the workshop before it was brought out to the lab.

View of the heat pump unit as it was on the development bench.

View of the data acquisition and control boards.  They are mounted to the foam, but not enclosed, since they generate heat and would change their own temperature a lot if insulated.

Thermistor plugged into the tubing.

Another view of a thermistor in a fitting.

Diagram of the water reservoir and flow.

Fully labelled image of the calorimeter core with LENR-Stick test cell isntalled.

Photo of the multi-wire LENR-stick probe with key parts labelled.

Diagram of the core of the calorimeter.

Calorimeter core with the multi-wire LENR-stick in place.

Malachi lifting the top two layers of the insulation up to expose the core of the calorimeter.

View of the core of the calorimeter with a resistance heater in place

View of edge of thermal isolation plates - two aluminum plates with a gap between them. Near the center of the plates are two heat exchanger blocks that the water runs through.

Another view of the thermal isolation plate

Top thermal plate of the calorimeter - temperature controlled water from the reservoir is pumped through a heat exchanger block mounted between rwo aluminum plates to help isolate the calorimeter beneath it from ambient temperature swings. Ambient isolation is key to making precice calorimetry, especially when you are measureing temperature rise to the milli-Kelvin.

Water reservoir for flow calorimeter. The tubes on the right go tot he solid state heat pump. The tubes onteh left go to the calorimeter.

Solid state heat pump - made from a thermo-electric assembly we had lying around, this can pump at least 200 watts out of the water reservoir. That is enough to handle at least a half dozen calorimeters simultaneously.

Water flow lines feeding the bottom plate, the top plate, and two lines to the core calorimeter. Note the precision flow adjuster valve that sets the rough flow range to the calorimeter.

A view of the soldering on the copper shell.

Entire copper calorimeter shell

Copper calormieter shell - connection end.

Copper calorimeter shell - Closed end. Notice that the closed end is fit with a very expensive, precision machined plug.

This is the thermistor and heater fittings. The orange/orange/white pair of wires goes to the thermistor. The other fitting is one of the heaters.

The thermistor and heater fittings

One of the two 1 watt heaters exposed.

View inside the water reservoir where the pumps can be seen with a filter.

View of the Calorimeter, the water reservoir, and the heat pump all together in the lab.

The calorimeter in the lab with the laptop for it.

View of entire apparatus in the workshop before it was brought out to the lab.

View of the heat pump unit as it was on the development bench.

View of the data acquisition and control boards.  They are mounted to the foam, but not enclosed, since they generate heat and would change their own temperature a lot if insulated.

Thermistor plugged into the tubing.

Another view of a thermistor in a fitting.

Diagram of the water reservoir and flow.

Fully labelled image of the calorimeter core with LENR-Stick test cell isntalled.

Photo of the multi-wire LENR-stick probe with key parts labelled.

Diagram of the core of the calorimeter.

Calorimeter core with the multi-wire LENR-stick in place.

Malachi lifting the top two layers of the insulation up to expose the core of the calorimeter.

View of the core of the calorimeter with a resistance heater in place

View of edge of thermal isolation plates - two aluminum plates with a gap between them. Near the center of the plates are two heat exchanger blocks that the water runs through.

Another view of the thermal isolation plate

Top thermal plate of the calorimeter - temperature controlled water from the reservoir is pumped through a heat exchanger block mounted between rwo aluminum plates to help isolate the calorimeter beneath it from ambient temperature swings. Ambient isolation is key to making precice calorimetry, especially when you are measureing temperature rise to the milli-Kelvin.

Water reservoir for flow calorimeter. The tubes on the right go tot he solid state heat pump. The tubes onteh left go to the calorimeter.

Solid state heat pump - made from a thermo-electric assembly we had lying around, this can pump at least 200 watts out of the water reservoir. That is enough to handle at least a half dozen calorimeters simultaneously.

Water flow lines feeding the bottom plate, the top plate, and two lines to the core calorimeter. Note the precision flow adjuster valve that sets the rough flow range to the calorimeter.

A view of the soldering on the copper shell.

Entire copper calorimeter shell

Copper calormieter shell - connection end.

Copper calorimeter shell - Closed end. Notice that the closed end is fit with a very expensive, precision machined plug.

This is the thermistor and heater fittings. The orange/orange/white pair of wires goes to the thermistor. The other fitting is one of the heaters.

The thermistor and heater fittings

Embedded Document