We just commenced loading of the Hydrogen into the Celani wire. We are loading at 4.6 Bar and 170C. We started at 3.5 bar H2 at room temp to be comparable to calibration runs with the Isotan wire in Helium, The Isotan in H2, and the just completed Celani Wire in He all starting at 3.5 Bar.
One early thing to note is that the resistance of the wire is dropping off quickly. Cooool!
Interesting data from the Run #2 in He starting at 3.5 bar compared to the Calibration run 3 in He at 3.5 bar
The measured cell temperature is running noticeably higher with the Celani wire compared to the Isotan. I haven't had time to do the same comparisons with the other temperature sensors. Look for that soon.
Meanwhile, the impedance remains interesting with every run. This time we see a dip in a similar place to the Isotan, but the overall slope remains positive. Fascinating!
Thoughts?
Comments
Review my site ... window repairs: stephenhtcfh.dreamyblogs.com/. ../...
cash every month because you've got high quality content.
If you want to know how to make extra money, search for:
Mertiso's tips best adsense alternative
The answer is yes. Those steps were manual adjustments to the voltage.
If yes - my question is irrelevant.
A critical reviewer would not be happy with that.
A critical reviewer of your experimentation would spot this anomaly and would want this cleared up - as the implication is there is an error/fault in your diagnostics.
Do you have a working hypothesis, WHY it works- if it works?
Wish you success, positive results beyond any doubt.
Peter
The impedance is being measured at DC by measuring the ratio of voltage to current.. As such it has no phase angle and is the same as resistance.
I don't have ripple numbers handy but it is in the millivolt range, The A to D conversions are averaged for several seconds, mostly eliminating ripple.
We are now reaching 15.5 ohms, starting from 18.4 ohms.
R/R0 is almost 0.84 now.
By looking at the slope asymptote, we should be able to get the wire down to 15.0 ohms.
By comment #3 of Robert Greenyer, indirect heating.
If it was a DC resistance measurement (assuming current supplied from a Switch-mode converter) could you please publish the ripple current(s) spec for uncertainty calculation?
If it was an Impedance measurement (resultant of real component, reactive component and the theta angle), could you please publish the reactive component(s) of Celani's wire as compared to control wires, at fixed temperature, in air? and supply frequency? angle?
The mainstream critics will have to look into these.
I've read so many skeptics moaning about the bad measure of temperature, hotspot, mistakes.... One mode to have more stable result about thermal measures is to work in isothermal mode with compensation.
I've read paper of mckubre
lenr-canr.org/.../...
that propose that classic isothermal mode.
I've read similar method in captors, like MEMS.
for you the idea could be to stabilise the temperature of the reactor to a fixed value, by controling the dead nichrome wire heating, while you make the active wire power stabilized.
you will have to make all the software change, use a very efficient control method to stabilize heat quickly without bouncing... but this can shut up some critics... and I'me very pessimistic about possibility to convince mainstream.
Thanks for the clarification! I figured it was likely beforehand. I would expect the higher impedance of the Celani wire would mean a higher temperature for the same current compared to the other Isotran, but could always be wrong. As you point out, at least it's easy enough to compensate for with a slight adjustment.
This is fascinating work!
I think I remember with the treatment Celani's wire went through, it increased the amount of oxidation in the wire. Oxidation should increase the impedance of the wire, so that may explain some of why Celani's wire has a higher resistance in He than the Isotran.
The other potential factor I can think of are the micro surface breaks in the Celani wire may also have the same affect.
Now, why there's a dip in resistance at a certain amperage... maybe that is some sweet voltage/current resonance spot for the wire. Otherwise.. I have no other guess as to why there's a random dip around 2 amps in both wires in inert atmosphere.
In the data from Helium runs 1 and 2 with we are seeing higher temperatures achieved by the Celani wire. That means the correlations developed with the other wires may need some adjusting to be valid. We'll see.
RSS feed for comments to this post